How To Create A Bootable Usb Flash Drive To Install Windows Xp

How to Setup Windows XP from USB drive?

Yous are hither: Tutorials > How to setup Windows XP from USB bulldoze?

Step1: Creating Rescue USB Drive

Commencement, nosotros need create a rescue USB drive which can boot the figurer. Please follow the steps,

Run PowerISO rescue media utility. You can download information technology here. On Windows Vista or above operating system, you may need ostend the UAC dialog to continue.
Insert the USB bulldoze yous intend to kicking from.
The utility will allow you choose Windows PE architecture and version. It is suggested to select 32-bit architecture and Windows PE 3.11. Click "Next" to proceed.
Select USB drive for output device, and select the right bulldoze from the listing. Click "Next" to proceed.

The utility will start creating rescue USB drive. It will check necessary component and automatically download missing component from the server.

Please detect that all existing data on the USB drive will be destroyed during this step. The program will alert you before writing the USB drive. Click "OK" to continue.

When information technology's done, copy the Windows XP setup files to the USB bulldoze. Please note that yous'll only need the i386 folder.

If no errors occurred in the above process, y'all should now be all ready to setup Windows XP from USB bulldoze!

Stride 2: Configuring the BIOS

You should now reboot and become into the BIOS configuration to kicking from USB. Instructions for doing and then vary wildly from system to system, simply generally entail the following:

Reboot the system.
While booting (before Windows starts loading), go into the BIOS configuration screen past hitting something like F1, F2, Delete or Escape. Hotkey instructions are more often than not provided on the screen.
Get to the section that contains your boot devices.
With your USB drive plugged in, the USB drive should be listed. If information technology isn�t, your organization might non support booting from USB. Bold that it is supported (every bit is the instance with virtually all modern hardware), promote your USB drive to the master boot device.
Get out from the BIOS configuration, saving all changes.

Please notice that you can seriously screw up your organisation past providing incorrect BIOS settings!

Stride three: Booting from rescue USB drive

Assuming that you lot properly configured your BIOS and your USB bulldoze supports booting, your computer should at present boot from the the rescue USB drive. Depending on the speed of your USB bulldoze, this may accept a while.

If it isn�t working, then double-bank check the following before making a scene:

Is your BIOS properly configured for booting from the USB device? (Is the USB device listed and does it have summit priority?)
Accept you correctly prepared the USB bulldoze in stride one? (Restart the procedure.)
Does your USB drive properly support being booted from? (Try some other one!)

Step 4: Prepping the Hd

Y'all need to make sure that your hard drive is partitioned and formatted properly. Specially if yous've had Linux or some other operating system on it, yous'll need to repartition and format it. The rescue bulldoze contain file manager and command line utility. Y'all can launch DiskPart for deejay partitioning and formatting from the command utility.

If you are sure that your difficult drive is gear up properly (i.east. it has only run Windows, information technology contains a valid FAT or NTFS partition) then you can condom yourself the hassle and skip this step.

Window XP doesn't support GPT partition. If your hard bulldoze is partitioned in GPT manner, you also need repartition and format the disc.

To repartition and format (This process will destroy whatever data on the hard bulldoze):

Click the icon on job bar to launch a control line Window.
Enter DiskPart to run the congenital-in disk direction utility.
Enter the commands needed to repartition and format your drive. For case, try the following:

select disk 0 (select the first disk. On your estimator, disk 0 may not be the right disk, you can use "listing deejay" to observe the correct disk.)

clean (purges the entire drive, essentially resetting it)

create division principal (creates a unmarried partition from the entire disk)

select partition1 (select the division created)

format fs=ntfs quick (format the partition to NTFS system, and practise a quickly format)

assign (assign the partition a drive letter)

exit (quits DiskPart).

Footstep 5: Launching Windows XP Setup from USB bulldoze

With your drive all ready, you can now launch the Windows XP setup with a few custom parameters. Permit's assume that the files are bachelor at E:\i386.

Plugging in a device now won�t work. Remember that all USB devices will need to be plugged in correct from the start while using the rescue drive.

Run the following command:

Run E:\i386\winnt32.exe /syspart:C: /tempdrive:C: /makelocalsource. Supplant C: with the drive yous want to install Windows to.
Continue with the installation. If asked to convert the installation volume to NTFS, answer No. The setup program incorrectly believes that your USB drive (if is formatted as Fat) needs conversion.

The setup program will and so silently close, which might brand you call up that something went wrong. Don't worry though.

Pace six: Continue Windows XP Setup from Hard disk

Reboot your system.
Unplug USB drive during post phase.
Change your BIOS settings back to boot from hard deejay once again as needed.
You lot tin can now continue to finish setting up Windows XP.

Annotation: The above guide works with Windows XP just. For Windows 10, Windows vii, Windows 8 / eight.i, or Windows Vista operating systems, delight refer to another guide at http://www.poweriso.com/tutorials/how-to-make-win7-bootable-usb-bulldoze.htm .